Molten metals simply slide off of the extra heavy duty coating of High-Temperature Silicone Rubber on all of these products (firesleeve), providing excellent burn-through protection.
Firesleeve withstands Molten Metal Exposure
Firesleeve Protects Wire Cable Hose
FireTape™  Silicone Rubber Coated Fiberglass Tape
High Temperature, Heat & Flame Resistant :  Non-Adhesive
500°F / 260°C Continuous Exposure:
Higher Intermittent

FireTape™
high temperature, heat & flame resistant tape is similar to our firesleeve except it can be installed in situations where tubular firesleeve cannot be used, as when industrial hoses, wires and cables cannot be disconnected to install a sleeve. (our firesleeve with velcro closure is also an alternative).

This high temperature tape is the perfect choice for protection of industrial hydraulic hoses and lines, pneumatic lines, fuel & oil lines, brake lines, wires, cables, tube and pipe from exposure to high and extreme heat conditions.  The extra thick special formulation of silicone rubber sheds molten metals, slag, welding splatter, electrical or grinding sparks and contamination.  This tape also provides protection from ozone, UV and abrasion and provides thermal insulation.

This tape is produced in high temperature oxide-red, however it can be painted with our liquid silicone to result in almost any color. Normally supplied in 100 foot lengths.

This tape is fabricated from a knitted fiberglass (fibreglass / glassfibre) yarn substrate, and is available in 5 standard widths: 1", 2", 3", 4" and 5". Due to the knit construction of the base material, this tape has the ability to stretch slightly across its width, but only minimally in its length.

This tape can also be used to wrap complex shapes or varying dimension tapered pipes.  Typically, the tape is overlaped by 50% when winding, which provides the entire assembly with stability.  Safety wire, band clamps, ties or End Wrap Tape can be used to secure the tape in place after installation.
Withstands Molten Splash & Welding Splatter.  Withstands 500°F / 260°C continuous exposure;
2200°F / 1205°C for periods up to 15 minutes and short flash excursions to 3000°F / 1650°C.

High Temperature Silicone Rubber Coated Fiberglass Heavy Duty Woven Tape & Wrap: Non-Adhesive
Heavy Duty Woven fiberglass (fibreglass or glass-fibre) tape coated with high temperature silicone rubber.

This tape is fabricated from a woven fiberglass substrate, and in available in widths up to 40" wide and lengths up to 150 feet continuous. Due to the base material being woven, this tape has very little elasticity or ability to stretch in any direction, although it is easily wrapped over even small diameter hoses, pipes, cables or wires. 

High Temperature Silicone Rubber 2 Side Coated Fiberglass Tape & Wrap: Non-Adhesive
Fiberglass (fibreglass or glass-fibre) tape coated on two sides with high temperature silicone rubber.

This tape is fabricated from a woven fiberglass substrate, and in available in widths up to 40" wide and lengths up to 150 feet continuous. 
Withstands Molten Splash & Welding Splatter.  Withstands 500°F / 260°C continuous exposure;
2200°F / 1205°C for periods up to 15 minutes and short flash excursions to 3000°F / 1650°C.
2 side coated silicone rubber fiberglass tape
Catalog Page & Pricing
MSDS
High Temperature Silicone Rubber Coated Fiberglass Tape
Catalog Page & Pricing
MSDS
Click Here for Spanish Language
Part Number
T-FG-SR
Part Number
T-FGHD-SRHD
Catalog Page & Pricing
MSDS
Part Number
T-FG-SR-S2
Return To Main Page
Share this page.....
Click Image
To Open
Catalog Page
T-FG-SA-19166 MIL I 19166 High Temperature Electrical Insulation Tape
1/15
Click Image
To Open
Catalog Page
T-FG-SA-19166 MIL I 19166 High Temperature Electrical Insulation Tape
Click Image
To Open
Catalog Page
T-FG-SA-19166 MIL I 19166 High Temperature Electrical Insulation Tape